
FlexStat 34 Operation Guide, Rev. R
CO
2
Level Is “Too High”
• See the CO
2
and DCV Sequences Are Not Work-
ing section above.
• To reduce nuisance complaints by occupants,
turn o the visibility of the CO
2
level rotation in
the display. See (Advanced) User Interface (UI)
on page 21.
DCV Menu Is Not Visible
• In the BAC-12xxxx/13xxxx/14xxxx models, DCV
Setup is visible only when an application witha
modulatingeconomizeroptionisenabled. See
Damper Setup on page 7.
Input Values Are Outside the Expected Range
• Check that ALL the input pull-up resistor
switches are fully latched in the correct positions.
See the Connections and Wiring section of the
relevant FlexStat Installation Guide. Asingle
incorrectswitchpositionmayaectmultiple
inputs.Allinputswitchesmustbelatchedin
eitherthe10KOhmorthe0–12VDCposition
evenifnoinputisconnected!Inputswitch
pairs(3-4,5-6,and7-8)mustneverhaveboth
switchessetinthesamedirection—ifswitch3
issettotheleft,forexample,4mustbesetto
theright(orviceversa).
• Check that the correct input type is selected on
the Inputs screen. A Type III thermistor is the
default on external inputs. See (Advanced) Inputs
on page 17.
• Check input wiring. See Wiring Issues on page 39.
• Check connected sensors.
• Using BACstage or TotalControl, check that the
input is not congured as “Out Of Service.”
• Restore the FlexStat to factory seings (see Reset-
ting the FlexStat on page 26) and recongure.
• For an external CO
2
sensor connected to IN9,
allow at least 15 minutes after installation for the
reading to stabilize.
Humidification/Dehumidification Issues
• See Humidity Setup on page 8.
Motion/Occupancy Sensor Does Not Work
• The initial rmware (R.1.0.0.0 and earlier) did not
support this sensor within the built-in selectable
programs. Custom programming was required—
see the FlexStatApplicationGuide. Upgrade to
the latest rmware for built-in support.
• After an initial power-up or restart, the motion/
occupancy sensor requires about 30 seconds
before it will begin responding to motion.
• The motion/occupancy sensor initiates override
only during “o” times in the schedule. See
Schedules on page 24.
• Check that the motion sensor is enabled and
detects motion. See Motion Sensor Setup on page
8.
• Using BACstage or TotalControl, check that BI6
(occ status) is not congured as “Out Of Service.”
• The FlexStat must be installed where there is a
clear view of typical trac area (reliable range is
out to about 33 feet). Remove or move obstacles.
Reinstall the FlexStat in a more optimal location
if necessary.
• Connect remote motion sensors to an input
(requires custom programming).
• For more information on detection performance,
paerns, conguration, programming, and other
issues, see the Motion/Occupancy Sensor section
in the FlexStatApplicationGuide.
Temperature Reading Is Incorrect
• Check that the correct °F/°C temperature scale is
selected—see Navigation on page 4.
• Fahrenheit decimal values are not displayed by
default but can be enabled in the User Interface
menu—see Show Temperature Tenths (Decimals)
on page 21.
• Check for the correct remote temperature sensor
conguration—see Sensor Setup on page 9.
• After applying power for the rst time (or after an
outage), allow the FlexStat to self-calibrate a few
minutes before verifying temperature reading.
(Allow BAC-13xxxx/14xxxx FlexStats with CO2
sensors to stabilize for about 30 minutes.)
• If the discrepancy is small, adjust the calibration
oset—see (Advanced) Inputs on page 17.
• Check that the thermistor (on models without
humidity sensors) is centered in its hole at the
boom of the case and has an air gap around it.
Commenti su questo manuale