Kmc-controls FlexStat Operation Guide Manuale Utente Pagina 8
- Pagina / 46
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
FlexStat 8 Operation Guide, Rev. R
When BAC-1xxxxx models have an application with
the CO
2
sensor ANDthemodulatingeconomizer
optionenabled, menu items for DCV(Demand
ControlVentilation) will appear. Forinformation
abouttheDCVoptions,see (Advanced) CO2 Sensor
(and DCV) on page 11.
Fan Setup
FAN SETUP
SPEEDS:
OFF DELAY (SECS): 180
UNOCC: AUTO
OCC: AUTO
HTG FAN: AUTO
CONSTANT SPEED
For heating applications, Heating Fan is set to Auto
by default but can be disabled if needed (such as for
an FCU that is factory wired to run at a xed speed
or for a baseboard heater without a fan). The Heating
Fan selection is only available when the application
supports heating and either Occupied fan or Unoc-
cupied fan is set to Auto.
NOTE: For a Fan Fail Alarm, see Sensor Setup on
page 9 and Alarms on page 23.
Humidity Setup
HUMIDITY SETUP
DEHUMIDIFICATION
HUMIDIFICATION
DEHUMIDIFICATION
DEHUM:
ENABLE
NOTE: If a dehumidication option is enabled, the
Space Humidity Alarm will also be enabled.
See Alarms on page 23.
NOTE: To see the dehumidication option in the
Additional Setup menu for a HeatPump
application, select an Aux. Heat option
other than None (the default).
Motion Sensor Setup
MOTION SENSOR
OCC OVERRIDE:
STATE: OCCUPIED
STANDBY: DISABLE
—OFFSET: 3° F
—TIMER (MINS): 30
ENABLE
A motion/occupancy sensor may be enabled (the
default) to trigger occupancy override (enabled by
default, but only functional during scheduled o
times) and occupancy standby in relation to the
scheduled on and o times. (See the chart.)
During scheduled OFF (unoccupied) times,
temperature is controlled according to the seing of
the appropriate heat or cool setback (see Setpoints
on page 25). Occupancyoverride (for 1 hour as a
default) starts when the sensor detects motion.
Temperature will start being controlled according
to the appropriate setpoint. Occupancy override will
end (with the default seing) 1 hour after motion
was last detected. The length of occupancy override
is congurable in the System menu. See System
Modes on page 25.
During scheduled ON (occupied) times, temperature
is controlled according to the seing of the appro-
priate heat or cool setpoint. If enabled, occupancy
standby sets the temperature back or up (according
to the heating/cooling mode) by the Oset amount
when no motion is detected for the Timer amount (30
minutes by default). The normal setpoint is restored
when motion is detected twice (to reduce false detec-
tions) within three minutes.
NOTE: Occupancy standby, when activated, lets
the temperature go down or up (according
to the relevant mode) by the Oset amount
(3° by default), not the Setback seing in the
Setpoints menu (which usually has a larger
temperature dierential meant for a longer
o time).
NOTE: When the Advanced DCV mode is selected,
Standbyisenabledbydefaultandwhen
revertingfromStandbybacktoOccupied
mode,thesetpointisrestoredby1°every
15minutes—to further conserve energy
according to the guidelines by Portland
Energy Conservation, Inc. (PECI). In
BasicorStandard DCV mode or no DCV
is selected, the setpoint value is restored
by the full amount immediately when
- Operation Guide 1
- (Click for details.) 2
- CAUTION 3
- Setpoint Adjustment 4
- Configuration 4
- Display Options 5
- Configuration (Setup) 6
- Advanced Menu 7
- (Advanced) CO 11
- Sensor (and DCV) 11
- (Advanced) Date/Time 16
- (Advanced) Inputs 17
- (Advanced) Restart/Restore 18
- (Advanced) Test 19
- (Advanced) Trend Logs 20
- COOL 22
- Date/Time 23
- Schedules 24
- System Modes 25
- Setpoints 25
- Resetting the FlexStat 26
- Restore Factory 27
- Network Connection 28
- Firmware Upgrade 29
- Programming (Custom) 29
- Maintenance 29
- Accessories 29
- Alarm, (False) Fan Fail 30
- Cover Binds on Backplate 31
- Display Is Blank (or Erratic) 32
- Display Keeps Resetting 32
- “SYSTEM ERROR” Is Displayed 32
- Analog Output Does Not Work 36
- Fan Does Not Run 36
- Firmware Upgrade Failures 37
- Wiring Issues 39
- Important Notices 40
- Reference 41
- Definitions of Terms 42
- Standby, Motion Sensor: 8 45
- KMCControls 46
- 19476 Industrial Drive 46
- New Paris, IN 46553 46
Prodotti e manuali riguardandi Sensori Kmc-controls FlexStat Operation Guide
Sensori Kmc-controls CSP-5002 Manuale Utente
(21 pagine)
(21 pagine)
Sensori Kmc-controls CTE–1103 Manuale Utente
(2 pagine)
(2 pagine)
Sensori Kmc-controls CTE–1108 Manuale Utente
(2 pagine)
(2 pagine)
Sensori Kmc-controls CTE-1101 Manuale Utente
(2 pagine)
(2 pagine)
Sensori Kmc-controls CTC-1612 Manuale Utente
(2 pagine)
(2 pagine)
Sensori Kmc-controls CTC-1622 Manuale Utente
(2 pagine)
(2 pagine)
Sensori Kmc-controls KMD-1162 Manuale Utente
(8 pagine)
(8 pagine)
Sensori Kmc-controls KMD-1183 Manuale Utente
(1 pagine)
(1 pagine)
Sensori Kmc-controls KMD-1281 Manuale Utente
(10 pagine)
(10 pagine)
Sensori Kmc-controls SAE-1062 Manuale Utente
(6 pagine)
(6 pagine)
Sensori Kmc-controls SAE-1162 Manuale Utente
(9 pagine)
(9 pagine)
Kenwood TM-431E podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Akcesoria żeglarskie Kenwood TM-431E.
Dostarczamy 1 pdf podręczników Kenwood TM-431E do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Commenti su questo manuale